Friday, June 7, 2013

Gee, 12+ year old bilge pump not working???

I started cleaning out the interior and the simplest thing to do was bring the hose inside and start with the simple green and scrubby. The water has to go somewhere and the bilge is the place. There is a garboard drain plug(threaded plug installed in the bilge to allow water to drain out when on the hard) in the bilge but it's up high enough that several inches of water can be in the bilge. So I brought the battery and solar panel from my truck camper and tried to hook up the electric Rule 500 pump. I suppose these cheap little units are not meant to be submerged for 12+years. So it was off to Hamilton Marine for a replacement. There is a nice Whale Gusher mounted in the cockpit but again I'm lazy and would rather let the sun and a SHURFlo 380 keep the bilge dry. Plus once I stick a float switch on it will empty when I'm not around and the boat is still far from rain proof:(  
Water level about 2" blow the floor. Very old bilge pump.

New SHURflo takes up the job. 

But the kink in the bilge discharge hose had to be fixed. 
And how does rainwater get inside? First there is these neat little cockpit drain the simply drains inside? I have no idea if this was the original idea but seems a little strange.

Mystery drain in front of cockpit.
Mystery drain open into engine compartment.
Then there are the actual side deck and cockpit drains themselves which where clogged, kinked and basically fell apart when I tried to remove the hoses to clear them. So they for now they also drain to the bilge:( The upper rear line(cockpit seat drain) was dry rotted and ripped apart in my hands and the upper foreground line(side deck drain) is collapsed with a perpetual kink. These two lines are combining with the cockpit sole drain.
clogged drain lines

There is also the old transmission shifter slot in the cockpit sole and if there were standing water the old engine controls openings. Plenty of things to fix before Phoenix can be left on a mooring unattended. 



P.S. Update to cleaning the deck. Forget using Simple Green and brushes, use a pressure washer! I needed to buy a 2700psi pressure washer for some house projects so I decided to try it on the filthy decks. With a 25deg nozzle it worked fantastic. It did remove some chipped loose paint but that needed removing anyway.   I finished the entire deck in the time it took to clean one cockpit locker! And the deck is much cleaner than I was able to do with the brush. 

Monday, June 3, 2013

Cleaning....

Certainly not the most exciting thing to do but every time I touch a surface dirt or paint chalk comes off on my hands. So today I spent several hours just cleaning. First came the mast and I attacked it with a hose, simple green in a squirt bottle , bristle brush,  a green scrubby pad. As I washed I inspected and liked what I saw. It was built in 1992 by Annapolis Spars Inc and is in generally great condition. The white paint is chipped in many spots all the way through the green primer to the aluminum but it's not bad enough to be stripped and redone. I may get some white Rustolium and touch it up but probably just wax it and be done. About the only real problem is the missing lower pins on the rigging. The yard managed to loose them all! 
Seriously moldy Main and Jib halyards


Then I climbed up and started on the cockpit. The entire boat is covered with at least 12 years of air pollution. Being on the hard near a major airport sucks. Those jets will turn a boat black in just a few weeks, so Phoenix took a ton of elbow grease just to get part of the cockpit cleaned up. The nonskid holds on to that junk tight. 
Even the topsides look better when cleaned:)
Starboard cockpit locker getting cleaner.
I got bored scrubbing and decided to see how simple green would work on seriously dirty teak.  Well it kinda works, but I broke down and mixed up an batch of water(3 qts)/TSP(1 cup)/clorox(2 cups) and that mix really does the trick! Still a lot of elbow grease but wow the results are great. After cleaning up the starboard coaming I can see doing some sanding and varnish. Really I'm too lazy to keep the teak clean and let it go silver because that also means black mold. I like the look of silver/gray teak but not when it's covered with black mold, which turns green when wet. Now that's ugly. But now that I've cleaned it up I suppose I need to finish the job and varnish. Certainly not the most important job, but having pretty teak and a clean hull make it more of a pleasure to work on the must have done list:)
A nice shade of green mold.

Mold does't look so bad when dry.

TSP/Water/Clorox quickly turns a nice shade of brown.

Left side(aft end) cleaned with TSP, Right side gets it next.

Sunday, June 2, 2013

Aux prower!

Poor old Phoenix was abandoned and her trusty old Atomic 4 was heisted, so what should I do about aux power? I considered and rejected Electric(Torqueedo) and a new outboard( Tohatsu 6hp Sailpro ) but choose instead…..drum roll please…..A 1957 Evinrude Sporttwin 10hp 2-cycle outboard. I scored this classic motor in Annapolis off craigslist for a whopping $75. Heck the sporty outboard bracket that I got from Bacon's Marine cost that much:)

Classic lines:)

Note the manual choke, low speed idle mixture and high speed idle mixture!

Cool clam shell cover!
I started the rejuvenation of the Sportwin. That will basically be a carb rebuild, new points, condensers, coils, plus and plug wires. Also cleaning and lubrication as needed. 

90 DegsF at 9am in Downeast Maine USA oh and I moved the mast off Phoenix:)





For Christ-sake please you southerners take your weather back! I decided to move the mast to ground level to improve movement around deck and to better evaluate what is needed to make the mast ready for sea. After some test lifts of the mast in place and getting a feel for the weight I decided it would be simple enough to lower it over the side using some 2"x4"x8ft studs and a 4:1 block and tackle. The 2x4 across the rear pushpit (the safety rail around the rear) was supporting the mast head and only stuck out about 3ft. This one was fine just laying on it's side. The forward 2x4 was counter levered much farther, maybe 5ft and the mast foot was much heavier so I ended up making a T with another 2x4. It may have been strong enough but I was a little worried by the bend and these are just cheap construction grade pine 2x4s. And once the T was built there was zero bend. 


The mast foot was much heavier, but I used the same procedure.  However, I should have left the mast head on the ground as the old sawhorse collapsed and dropped it to the ground.  I really should have seen this coming:( As soon as I lifted the mast foot at the bow, the mast wanted to slide downward to the rear. Then when I reset the mast, the saw horse tipped. I've really got to get "THINK IT THROUGH" tattooed on my forearm or something. Luckily the ground is soft and no harm done.

After some quick measurements to determine if this "new" mast matches the original mast/boom dimensions I cleared up the area and retreated to the basement for other projects and the coolness.